scenery backdrops

unadjusted photo showing new backdrop - click on image to enlarge

In my mind, the backdrops of a model railway are a critical part of the illusion. In this country, there seems to be a distinction between 'dioramas' and model railways. With a bit of forethought, even a long model railway can still be a diorama. The requirements are more demanding however. The backdrops should be taller, there should NEVER be right angled corners in the sky, and the transition between the model and backdrop has to work through a wide arc of viewing angle. Lighting pelmets are used above the model.

This means that part of the operation of the model is from the front although we are now going to add a rear fiddle yard. In my mind this gives better inter-action with the public and the operator does not detract from the illusion by appearing 'King Kong like' over the back of the model.

We started off with this 360 panoramic put together with Autostitch. A bit up and down, but my son had a hangover that day!

To start off, a decent high resolution 360 panoramic of the required sky is needed. One has to choose the type of sky needed and be prepared to drop everything and go out with the camera when it arrives. Devon and Cornwall have rather typical cloud formations so it was some time before a similar situation occurred in Herefordshire. Luckily, my son, (the family photographer) was visiting us when the 'sky to die for' arrived. Sadly, he also had a bit of a hangover, so the resulting shots were a tad out of alignment to say the least. We used a programme called Autostitch which saved the day!

The sky had to be blown up to 10.2 metres long. This large, there was a small degree of pixilation. We used the 'median' facility in Photoshop to deal with this. We pasted a metric scale along the bottom and up the side of this long image. We were then able to collage hills, trees, etc in the right places along the image.  We adjusted image colours to match our model, allowing a certain fade to give the effect of distance.

backdrop for harbour section

The image was converted to CMYK format and printed on gloss vinyl. Experience has shown that this gives us the best resolution. We have tried self adhesive paper and matt vinyl, none of which works so well. Be careful, as conversion to CMYK may need more colour equalisation. Your computer monitor might not be set up to see CMYK properly. Best print a test section with the same printer that will be used. If the model is to be kept in direct sunlight, use UV resistant inks. Once the ink on the vinyl has 'gassed off' which takes about 12 hours, a clear matt vinyl is then laminated over the print.

It is not every company that is interested and will make to effort for model railways. We have been luck to find Clancy Wilson of Signrite who has worked with us to develop a perfect technique for printing and applying backdrops.

We cut the roll of backdrop at a joint near the middle, attached the aluminium panels temporarily to our sitting room wooden floor with double sided tape. One other advantage of using vinyl rather than paper is that it is applied using a mister with water and a little detergent so things can be moved around.! We first experienced problems attaching the backdrop to the curved sections. The aluminium panels are very thin and if they lose their shape during the application process, the vinyl will come away later. They must be supported in the correct shape during application.

Once attached to the backdrops, the interface between model and image can been softened with trees where necessary. Hard edges are much harder to hide unless you have got the colours perfect. I have to say, we had three goes at this until we had a perfect job.

Clancy Wilson, head man of Signrite fitting the new backdrops

the next panel is laid down and is ready for the vinyl

unadjusted photo showing new backdrop - click on image to enlarge

This is another backdrop printed by Signrite of Oldham in 1959. The model, built by us, is in fine scale N and is bound for Dubai. - click on image to enlarge

trouble with horizons

We had intended to show a vague sea/sky horizon behind the port section. It did not work as it looked quite wrong with different viewing angles. We were forced to fall back to receding cliffs only which work better.